In recent years, China's semiconductor lighting market has grown rapidly, especially in April 2009, the National Science and Technology Ministry issued a "Response on the approval of the "Ten Cities and Ten Thousands of Semiconductors" semiconductor lighting application project pilot work, the LED is in The application of road lighting has pushed to a new climax. However, while the industry is developing at a high speed, there are some problems. Recently, Wang Xiaoming, director of the Engineering Department of Shanghai Street Light Management Center, pointed out that there are too many companies who are keen to apply LED lighting technology to road lighting. Whether it is a traditional street lamp enterprise or a non-traditional street lamp enterprise, it appears in the development and production of LED street lamps. A series of big and small problems and drawbacks. If these problems cannot be solved well, in practical applications, LED street lights will encounter more objective resistance and doubts, including those from the street lighting operation and maintenance management unit.
To sum up, enterprises should focus on the following four major issues in the development, production, and promotion of LED street lamps:
The first is the shape and structure of the luminaire. The shape of traditional street light fixtures, such as sodium light source lamps, light sources and electrical appliances are generally divided into two parts, which may vary from product to product, but in general, they are basically the same. However, the particularity of the LED light source, the way of light distribution is different, and now the shape of the LED street light fixture can be described as a variety of patterns, many of which can not meet the operational requirements of the lamp, and even some enterprises use indoor indoor standards for outdoor street lights. In addition, the connection between the LED lamp and the lamp post is also problematic. Almost all the LED street lamps are fixed by screws, and few hoop bolts are fixed. It is possible that the installation process is simple, so the manufacturer spends a little effort on this. However, for the operating unit, safety production is the basis, and the connection of the luminaire is directly related to the safe operation of the luminaire, so the degree of attention to it is even greater.
Followed by the weight of the luminaire. The weight of the luminaire is very important, but the general LED manufacturers do not have this awareness, or do not think too much about this. LED luminaires for heat dissipation, the luminaire's outer casing may be heavier than conventional luminaires. However, excessive weight will have an impact on operation and maintenance.
The third is the issue of replaceability of the luminaire components. LED street light components generally have LED chips, power supplies (drivers), and lamp housings. The main components are: power supply (driver) and chip. In general, LED luminaire chips cannot be replaced, and the power supply (drive) can be replaced. However, the replacement of some product power supplies (drivers) is not convenient enough, or it takes too much time to replace them in the field. In addition, the current life of LED lamps is generally 30,000 hours, the longest is 50,000 hours. If the LED chip cannot be replaced, only the entire luminaire can be replaced at that time, resulting in a large waste.
The fourth is the life of the power supply (driver). The power supply (driver) is a very critical component of current LED luminaires. Because the power supply (driver) of many LED luminaire manufacturers is not produced by themselves, sometimes the quality of the LED luminaire itself is good, but it is often inadvertently planted on the problem of the power supply (driver).
In fact, whether it is the quality or life of the LED itself, or the life of the power supply (driver), it is the embodiment of the quality and life of the LED street lamp itself. The quality assurance of the LED lamp should include these two aspects, that is, the life of the LED street lamp 3 10,000 hours or 50,000 hours should include the quality and life of the power supply (driver). At present, the situation on the market is that the general LED lamp manufacturers only guarantee the quality of the LED chip, and the life of the power supply (driver) is another matter. Manufacturers generally guarantee 2 years of majority, less than three years, and too few in five years. Therefore, the development of LED street light fixtures now has a new bottleneck - power supply (driver), and its quality assurance has restricted the development of LED street lights. This should attract the attention of the production companies.
Plug-in fuses are designed to be inserted into the fuse box. Fuse is small safety part in an electrical device or piece of machinery that causes it to stop working if the electric current is too high, and so prevents fires or other dangers. Fuse in the abnormal current increases to a certain height and heat, its own fuse to cut off the current, to protect the safe operation of the circuit fuse protection power equipment with current overheating damage, avoid electronic equipment serious damage caused by internal fault. When a circuit breaks down or is abnormal, the current increases with the current and the increased current may damage some important components in the circuit, and it may also burn the circuit and even cause a fire. If correctly placed in the circuit fuse, the fuse will be abnormal current increases to a certain height and heat, its own fuse to cut off the current, so as to protect the safe operation of the circuit.
Auto Plug-In Fuses,Plug-In Style Fuses,Blade Fuse,Mini Auto Plug-In Fuse
Heshan Jianhao Lighting Industrial Co., Ltd. , http://www.sunclubtw.com